Reloading Aids
Reloading Aids - Basics needed for precision work. Includes The AutoTricklerV4, The AND range of scales, RBST precision Calipers, CLARX Magnifying headset., Headspace and bullet comparators and more.
MI AutoTricklerV4
AutoTricklerV4 Inspired by an auger (and refined through simulation, testing, and iteration), a large tube with deep spiral grooves pours bulk powder at rates up to 50 GN/s, ramping down smoothly to within 1-2 grains of the target. Works with fine ball powders like CFE223 and H335 Works with large kernel powders like N570 and H50BMG Maximum flow rate ~50 GN/s for large caliber rifle Integrated electronics and motors with fixed cabling Acrylic panel and silicone pad..
MI V4 Replacement Windows
Replacement Windows for the V4 Auto Trickler - Pair of replacement acrylic windows for the front and back of the V4 housing...
MI V4 Spare Parts Kit
Please note, the V4 AutoTrickler kit comes with everything below. You should not need to replace these parts through regular use (i.e. they will not wear out). Some people like to get a second cup and some people have cracked their windows by dropping them. We've bundled these parts for convenience, but do not feel like this is a necessary purchase. Includes: Glass Cup V4 Centering Tray V4 Funnel 2x V4 Windows V4 Timing Belt (small tube) V4 Timing Belt (large tube) If you..
V4 AutoTrickler / AND - FX COMBO
AND FX120i scale and V4 Trickler combo..
V4 AutoTrickler /AND - FZ COMBO
AND FZ120i scale and V4 Trickler combo..
MI V4 Hopper
The AutoThrow powder hopper is made from PETG and incorporates a valve which blocks the flow when rotated. This hopper holds over 1 lb of powder. Hopper cover included. V3-style has an X and O mark to indicate whether it is open or closed. Fits any V2 or V 3 AutoThrow. V4-style is designed to lock in place on a V4 AutoTrickler and cannot be removed unless the hopper is closed. V3-style is displayed..
MI V3 Electronics
Replacement Board for the V3 Autotrickler..
MI V3 Spare Parts Kit
Includes: Glass Cup V3 Centering Tray V3 Funnel V3 AutoTrickler Pulley Belts (5) Roof Clips (4) Not suitable for V4 AutoTrickler...
MI V3 Timing Belt
Timing Belt for V3 Auto Trickler This belt does not wear out over time under normal use and you should never need to replace it. The V3 style is for the toothed pulleys on the V3 AutoThrow. It will not fit the V2 AutoThrow. The V4 has two different sized belts for each tube. If you do need to replace your belt please contact us for instructions before attempting to disassemble AutoTrickler or AutoThrow...
MI V4 / V3 Cup
Cup for V4 and V3 Auto Trickler Cup for the V3 / V4 Autotrickler..
MI V4 Timing Belt Set
Timing Belt for V4 Auto Trickler The V4 has two different sized belts for each tube. If you do need to replace your belt please contact us for instructions before attempting to disassemble AutoTrickler or AutoThrow...
MI V3 Motor Cable
This cable fits either the AutoTrickler or AutoThrow motor. The motor end of this cable includes strain relief heatshrink to keep it from bending. Avoid flexing the ends and ensure this stays in place. Always disconnect the cable before moving the AutoTrickler to empty powder in order to avoid flexing the ends. If the motor is shaking in place and not turning, the most likely reason is one of the four wires in this cable is broken. Check both ends of the cable and try swapping the cab..